The “file is too large for the destination file system” error is caused because of the FAT32 limitations. If you guys are well aware of a lot of file systems, then you guys must have a little idea of their limitations. A file system is actually a method or structure used via operating systems for identifying and organizing files on the disk. Windows basically uses the exFAT, FAT32, FAT, and NTFS file system. Just read this article to know all about How to Fix a File that is too Large for the Destination File System. Let’s start!
All these file systems come along with many limitations. Whenever you format a hard drive along with FAT32, it will not let you add an individual of up to 4 GB. To fix the errors and transfer files successfully. The only solution is just to replace the system of your hard drive from FAT32 to NTFS as well. The maximum size supported via FAT32 is 4 GB, however, NTFS can support more than 16 TB. This difference in their limitations results in the “file is too large for the destination file system.”
It can also be fixed easily via applying a lot of solutions. It was vital for you to know the reason so that the solutions can be implemented properly as well. And remember that in any circumstance, this error will not permit you to save files higher than 4GB as well.
Contents
How to Fix File is too Large for the Destination File System
What is a FAT32 File system?
The earlier version of Windows like Windows 95 OSR2, Windows 98, and Windows Me used an updated version of the FAT (File Allocation Table) file system actually. This updated version of FAT is called FAT32 that actually permits for a default cluster size as small as 4KB and also includes supports for EIDE Hard disk size that is larger than 2 GB. However, in the current environment, they cannot support large sizes and therefore, have been replaced via NTFS (New Technology Files System) system since Windows XP as well.
Now you guys know why you’re receiving the above error it’s time you guys should know how you can fix this error. So without even wasting any time, let’s see how you can fix this error via the below-listed troubleshooting steps.
Compressor Split the big files
When the file size is too large then compress or split it in order to save it on your USB. This will help in saving it to your USB drive instantly even when it is FAT32 format.
- Start via by right-clicking on a folder of files that you want to split and compress.
- After that, select the option “add to archive” from the options shown. Any large file can split into a smaller one, also including movies, videos, documents, etc. This way, users can share the video over the internet effortlessly as well.
- The option that permits you to split a file or folder is “Split to volumes, bytes.”. Under these options, you can choose the profiles that exist there or type the maximum size of the output file.
- If you guys don’t know then let us tell you that you can choose from the preset profiles too and them instantly.
- The default values accepted here are numbers such as 1029384 kb etc. Some of you guys know this, right? How to convert kb into MB or GB?
- Tap on “Ok” now because WinRAR will start compressing the source file and it will then split it into small compressed files containing preset sizes as well.
Converting FAT32 file system to NTFS without data loss
- Tap on Windows Key + X and then select Command Prompt (Admin).
- Now check what letter assignes to your USB flash drive or your external hard drive?
- Then just enter the following command in cmd and hit Enter:
Note: Make sure to replace the drive letter with your own Device drive letter as well.
Convert G: /fs:ntfs /nosecurity
- Now, wait for few minutes for the conversion process in order to complete as it will take some time relying on your disk size. If the above command fails, then you have to run Chkdsk (Check Disk) command to fix the drive.
- So in the command prompt window type the following and click on Enter: chkdsk g:/f
Note: Just change the driver letter from g: to your own USB flash drive letter.
- Now just again run the Convert G: /fs:ntfs /nosecurity command, and this time it would be successful.
- Next, try to copy large files in the device earlier, providing the error ‘The file is too large for the destination file system.’
- This would successfully Fix The file that is too large for the destination system error without even losing your existing data in the disk.
Format your Device using the NTFS file system
- Right-tap on your USB drive and choose Format.
- Now just change the file system to NTFS (Default).
- Next, in the Allocation unit size dropdown choose Default.
- Tap on Start and if asked for confirmation click OK.
- Now let the process finish and again try to copy the files to your drive.
Conclusion
Well, That is all from my side. If you want to know more about this article or have any queries. Then feel free to ask me anything in the comments section below.
Have a Good Day!
Also See: How To Do An Advanced Search On Facebook
